The pitch is 22 yards (20 m) or one chainin length between the wickets and is 10 feet (3.0 m) wide. It is a flat surface and has very short grass that tends to be worn away as the game progresses. The "condition" of the pitch has a significant bearing on the match and team tactics are always determined with the state of the pitch, both current and anticipated, as a deciding factor.
Each wicket consists of three wooden stumpsplaced in a straight line and surmounted by two wooden crosspieces called bails; the total height of the wicket including bails is 28.5 inches (720 mm) and the combined width of the three stumps is 9 inches (230 mm).
Aerial view of the MCG displaying the stadium, ground and pitch
Four lines, known as creases, are painted onto the pitch around the wicket areas to define the batsman's "safe territory" and to determine the limit of the bowler's approach. These are called the "popping" (or batting) crease, the bowling crease and two "return" creases.
A wicketconsists of three stumpsthat are hammered into the ground, and topped with two bails.
The stumps are placed in line on the bowling creases and so these must be 22 yards (20 m) apart. A bowling crease is 8 feet 8 inches (2.64 m) long with the middle stump placed dead centre. The popping crease has the same length, is parallel to the bowling crease and is 4 feet (1.2 m) in front of the wicket. The return creases are perpendicular to the other two; they are adjoined to the ends of the popping crease and are drawn through the ends of the bowling crease to a length of at least 8 feet (2.4 m).
When bowling the ball, the bowler's back foot in his "delivery stride" must land within the two return creases while his front foot must land on or behind the popping crease. If the bowler breaks this rule, the umpire calls "No ball".
The importance of the popping crease to the batsman is that it marks the limit of his safe territory for he can be stumped or run out (see Dismissals below) if the wicket is broken while he is "out of his ground".
Pitches vary in consistency, and thus in the amount of bounce, spin, and seam movement available to the bowler. Hard pitches are usually good to bat on because of high but even bounce. Dry pitches tend to deteriorate for batting as cracks often appear, and when this happens to the spinners can play a major role. Damp pitches, or pitches covered in grass (termed "green" pitches), allow good fast bowlers to extract extra bounce. Such pitches tend to offer help to fast bowlers throughout the match, but become better for batting as the game goes on.
Each wicket consists of three wooden stumpsplaced in a straight line and surmounted by two wooden crosspieces called bails; the total height of the wicket including bails is 28.5 inches (720 mm) and the combined width of the three stumps is 9 inches (230 mm).
Aerial view of the MCG displaying the stadium, ground and pitch
Four lines, known as creases, are painted onto the pitch around the wicket areas to define the batsman's "safe territory" and to determine the limit of the bowler's approach. These are called the "popping" (or batting) crease, the bowling crease and two "return" creases.
A wicketconsists of three stumpsthat are hammered into the ground, and topped with two bails.
The stumps are placed in line on the bowling creases and so these must be 22 yards (20 m) apart. A bowling crease is 8 feet 8 inches (2.64 m) long with the middle stump placed dead centre. The popping crease has the same length, is parallel to the bowling crease and is 4 feet (1.2 m) in front of the wicket. The return creases are perpendicular to the other two; they are adjoined to the ends of the popping crease and are drawn through the ends of the bowling crease to a length of at least 8 feet (2.4 m).
When bowling the ball, the bowler's back foot in his "delivery stride" must land within the two return creases while his front foot must land on or behind the popping crease. If the bowler breaks this rule, the umpire calls "No ball".
The importance of the popping crease to the batsman is that it marks the limit of his safe territory for he can be stumped or run out (see Dismissals below) if the wicket is broken while he is "out of his ground".
Pitches vary in consistency, and thus in the amount of bounce, spin, and seam movement available to the bowler. Hard pitches are usually good to bat on because of high but even bounce. Dry pitches tend to deteriorate for batting as cracks often appear, and when this happens to the spinners can play a major role. Damp pitches, or pitches covered in grass (termed "green" pitches), allow good fast bowlers to extract extra bounce. Such pitches tend to offer help to fast bowlers throughout the match, but become better for batting as the game goes on.
No comments:
Post a Comment